臺虎鉗使用說明書
Bench vice operating instruction
1、用途application:
臺虎鉗是用來加持工件的通用夾具。裝置在工作臺上,用以?shī)A穩加工工件,為鉗工車間必備工具。轉盤式的鉗體可旋轉,使工件旋轉到合適的工作位置。鉗工的大部分工作都是 在臺鉗上完成的,比如鋸,銼,鏨,以及零件的裝配和拆卸。 臺虎鉗的規格以鉗口的寬度表示,本次提供臺虎鉗規格為200mm。
Bench vice is used to clamp workpieces. It is installed on the work stations to clamp the workpieces. It is an necessary tool in the schlosserei. Rotating disc type clamp body can revolve so that make the workpiece rotate to the suitable place. Most work of fitter are finished on the bench vice. For example the saw, the file, the chisel and components installing and dismantling. The specification of bench vice is expressed by the width of jaw. The bench vice we supplied is 200mm.
2、使用方法operating instruction
臺虎鉗在鉗臺上安裝時,必須使固定鉗身的工作面處于鉗臺 邊緣 臺虎鉗 以外,以保證夾持長條形工件時,工件的下端不受鉗臺邊緣的阻礙。
When the bench vice is installed on the vice stand, you need make the working face on the vice stand outside edge. So that when the bench vice clamps the long workpiece, it will be not hampered by vice stand.
在鉗桌裝上臺虎鉗后操作者工作時的高度比較合適,一般多以鉗口高度恰好與肘齊平為宜,即肘放在臺虎鉗最高點半握拳,拳剛好抵下顎,鉗桌的長度和寬度則隨工作而定。
The height of operator working will be suitable because the bench vice is installed on the work bench. Usually the jaw height is flushed with elbow just right. This is ok. Put the elbow on the bench vice peak and half clenched fists that the fist just support the mandible. Length and width of work bench will be decided by the work.
夾緊工件時要松緊適當,只能用手板緊手柄,不得借助其他工具加力。
Appropriate degree of tightness when clamp the workpiece. Just tight the hand shank by the hand only. Do not add strength with the help of other tools.
(2)強力作業時,應盡量使力朝向固定鉗身。
When work strongly, you need try your best to make strength facing to clamp body.
(3) 不許在活動鉗身和光滑平面上敲擊作業。
Do not knocking on the clamp body and smooth surface.
(4) 對絲杠、螺母等活動表面應經常清洗、潤滑,以防生銹。
Clean and lubricate the surface of lead screw and nut. So that it will not rust.
聯系方式:0523-86131966 0523-86137409
CopyRight ? 2013 江蘇劍魚臺鉗有限公司 All Rights Reserved 備案號:蘇ICP備17008514號
【服務熱線】86-523-86131966 【企業郵箱】hongtai@www.jerryconklin.com
【公司地址】江蘇省泰州市醫藥高新區無量寺路8號